Workshop on making a clip "Bouquet of tulips"

The following materials will be required to create the "Bouquet of Tulips" jewelry:
- a big clip for hair.
- a ribbon of brocade of silver color with a width of 25 mm.
- stamens with large beads on the edge.
- white cabochon with a diameter of 12 mm.
- satin ribbon in white shade with a width of 25 mm.
- thermal gun.
- scissors.
- sewing thread with a needle.
- lighter.
Making jewelry.
First you need to prepare segments 10 cm long. They will be required to create tulip buds. In total, such pieces should be made 6 pieces.
Then it is necessary to make segments 6 cm long. They will be required for the manufacture of the outer petals of each flower. In total, 6 pieces need to be prepared.
Next, you need to start creating flowers. To do this, you need to take one long segment and scorch off its sections with a lighter, protecting them from shedding. Positioning the part horizontally in front of you, unfold with the wrong side up. Then the corner of the left edge must be bent to the edge line.
The created corner must be folded in half.
Now you need to thread the sewing thread into the needle and tie a knot at the edge. Then with a needle you need to do an even line of small stitches. The seam should be laid from the edge of the corner, at the same time fixing its addition.
The line should run along the entire part, not reaching the edge of 2 mm. The second seared edge of the segment must also be wrapped, completely repeating the actions on the left side.
Without trimming the thread, the created line needs to be pulled a little and make two stitches.
Now starting from the corner, the segment should be twisted into a soft tube, the position of the tape should be fixed with the thread left. Having made a few twists, the thread can be cut.
It turns out a small bud, from the remaining 5 long segments you should make the same blanks, repeating each action exactly.
Now from the remaining small segments you need to make the petals. To do this, taking one part, you need to position it horizontally in front of you and tuck the corners on both sides. Holding the part in this position, it is necessary to do a simple stitch along the edge strip with a needle for runes.
The stitch should be pulled down, and several fixing knots should be made so that the petal retains its shape.
The resulting petal should be fixed on top of one of the prepared buds. Having sewn a petal, the thread can be cut.
It turns out an unopened tulip bud. From the remaining segments, you should prepare the same single petals, which then need to be fixed on the buds.
The result will be beautiful tulip flowers.
Now for the flowers you need to make leaves. To do this, you need a silver brocade tape. From it, 5 segments of 10 cm should be prepared.
These segments must be folded in half along their length, additionally squeezing the fold line with your fingers.
Next, remove the corner by cutting it diagonally from the fold line to the upper left corner.
The resulting edge must immediately be scorched, simultaneously soldering two layers of tape and protecting the fabric from shedding.
The resulting sheet must be straightened, giving it volume.
In the middle of this leaflet, paste the created tulip bud.
From the remaining ribbons, you need to make the same leaves, in the middle of which you should glue the flowers.
Now you can start assembling the jewelry. Taking a piece of white tape with a length of 8 cm, you need to singe its slices and place it face down. One bud should be attached to its left edge.
On two sides of the flower you need to glue two stamens with large beads on the edge.
On top of the stamens, on both sides of the bud you need to fix the flowers.
The remaining three flowers must be fixed in one row, covering them with the junction of the first buds.
The small edge of the base tape has remained untouched; it will come in handy later. Now you need to prepare a large bow for decoration.
To do this, you need a piece of white tape, 16 cm long.
It should be turned upside down and outlined in the middle, drawing a few lines with a pencil.
To the middle of the segment, you now need to wrap the edges of the tape, slightly applying them.
Having folded the part, you need to hold it with your fingers.
With a needle threaded, it is necessary to flash the middle of the part.
Now you need to tighten the thread and fasten the seam.
It turns out a small bow. Further from a piece of 5 cm silver ribbon you need to make a small bow.
It remains to combine these two bows by sticking one on the other.
Now, two pieces of 6 cm each from a white ribbon will be required to create bow tails.
Their edges need to be cut off at a slight angle and immediately scorched by fire.
Then laying the parts on top of one another, they should be glued together.
The resulting tail must be attached to the ribbon of the base of the decoration.
Then it remains to fix the prepared double bow.
The middle of the bow must be complemented with a white cabochon.
From the wrong side, the prepared bouquet needs to be supplemented with leaves of silver ribbon.
On top of the fixed leaves, you need to attach a large clip, placing it along the decoration.
It remains to expand the bouquet and spread the leaves and flowers.
The bouquet is ready!

Watch the video: Essential oil distillation workshop clip with Dan Riegler (May 2024).